HHO SWISS INOX 4 SPIRAL CELL + GAS PRODUCTION TESTS

Here is what I do not understand. I have seen many such videos where these bubblers are made to be attached to a car.

So, you draw power from the alternator [burning gasoline] to generate H2 and O2 gas, which is then fed back into the car as a fuel supplement.

There are high losses in converting the water to 2H2 and O2, as evidenced by the heat in the bubbler. The gas being sent back to the engine has less energy than the gasoline used to create it. You'd be better to simply burn the gasoline.

when you have the caseing attached as negative and the spiral as possative, it is the caseing "wall area" that is producing gas, possative produces oxogen, try switching connections arround, i had simmilar in one of my cells, s/s caseing, it produced better, less heat too… nice work guy…
thom scotland.

SUPER work BTW

maybe the issue with the blade cell has something to do with the putty material u used conducting also? it may be porous enough to retain water

we have found if you start with 3/4 tsp of baking soda to 1 gallon of d water. it will produce at start 15-20 amps, and after an hour of heating it will increase to 30-35 amps due to heat, which works out great.

peppoj I get both Hydrogen and Oxygen from all my cells
AMOX

in the first cell do you get both hydrogen and oxygen, or just hydrogen?

the container is a bomb! hho is a very explosiv gas, put in a steel container can amplafay power of explosion ! electrical conexions can make flahs in hho gas and explosion ! put the electrical conexion downstairs in electrolit not in gas hho ! upstairs only hho gas can remain too be colected safety !

You need to alternate all cells pos and neg there is n use for neutral.

i got a 60 amp charger o_O

I will see what I can do to have you and others like you satisfied…………
AMOX

qsl multi 63

To put it better…the amount of gas u can produce is related to the amount of power (watts) you use. let's assume you're using a 12v dc battery, at 20 amps you're pulling 240watts. 12volts at 40 amps is 480 watts. you produce twice as much hho gas at 40amps, but use twice as many watts.

If u noticed, the more amps being pulled the more hho gas u produce. The production of hho gas has nothing to do with the design of the cell, the design of the cell has everything to do with resistance. the lower the resistance the more amps u can pull, thus giving u more hho gas.

Find out what PMW is and how to connect it to you HHO gen.
Don't use salt use baking soda salt makes Chlorine.
HHO gas floats up to the ceiling in a house do project outside.
Use wind power while driving down the road the wind resistance
against the car and a wind turbine connected to the HHO cell.
Search for "simple generator" on YouTube.

This seems to be a far better than average design. Keep going. You are progressing well. These seem to be well thought out experiments, and It seems you are making good progress.

Are you planning to publish results?

you can weld with hho steel and anything, but below 3 liters per minute, ye you can't weld..

well, what happens if you use a dubble casing,where the spiral is neutral in the middle, the outer casing is possitive and the inner casing is negative?

There a cars running under propane power already. Why cant they be converted to run on hydrogen?

HELLO MY FRIEND REALLY NEEDS YOUR HELP I SEE SEVERAL PROJECTS THAT SAME USING COPPER GAVE RIGHT THEN I AM SENDING YOU SOME PHOTOS OF THE COIL THAT I DID WITH COPPER BUT DIDN'T HE WORK FOR THAT I ASK FOR YOUR HELP SO THAT I CAN UNDERSTAND WHAT I DID WRONG (IS THE COPPER COVERED WITH THE VARNISH WILL BE THAT THE PROBLEM IS THAT?? SHOULD I REMOVE THE VARNISH? do you have email to me send you my photos??

Only the negative terminal produces anything, that is why your middle terminal is the only one producing.

Where can we buy your cells?

Super gebaut !

Aber was benutzen sieh für eine Flüssigkeit ?

#1 !

You are making water heaters, lol.. Water splits around 1.8 volts and the higher the voltage is over that the more of your energy is converted to heat and not hho.. You need to measure gas volume over time at given am draw and calculate watt/minuets for liter of gas. Then you will know your efficiency. Best of luck to you! Nice welding BTW..